|Total Living Area:||1301 sq ft|
|Main Living Area:||893 sq ft|
|Upper Living Area:||408 sq ft|
|Garage Type:||N/A or Unknown|
|Foundation Types:||Crawlspace - * $425.00
Slab - * $425.00
Stem Wall Slab - * $425.00
|Number of Stories:||2|
|Max Ridge Height:||30'11 from Front Door Floor Level|
|Primary Roof Pitch:||0|
|1st Floor Master:||Yes|
View an actual, LIVE cost report. This report is for demo purposes only. Not plan specific.
A: Hi! Sorry but we don’t have this information seeing as the plan has never been in only basement foundation Thanks! Jessica
A: The insulation for the ceiling is R-40
A: Hi there! I cannot send this but I can confirm that our plans meet the ICR 2012 Thanks! Jessica
A: Hey there! The dimensions of this house do not include the decks/porches Thanks! Jessica
A: Hi there! The basement is approx 8’-0’’ Thanks! Jessica
A: Hi there, For this plan, the foundation is a walkout basement so the pier foundation would have to be done via mods The exterior walls are in 2x6 and the R value for the mis R-24 Thanks! Jessica
A: Good morning, It is 39’-6’’ from the highest point to the ground level of the walkout foundation Thanks!
A: Good morning, For this house you can add the deck that is 36’ x 10’ Thanks!
A: Good morning, The material list is sent in .pdf format Thanks! Jessica
A: Good morning, Actually no, we unfortunately have no interior photos for this house plan. Regards, Jessica
A: Hi! The basement is the same dimension as the main floor but with no divisions. The square footage is 893 square feet. Jessica
A: Good morning, The hot water heater is located in the basement. For the furnace and AC, the customer will need to decide where they want it but it can quite easily be planned in the basement. Jessica
A: Hello, Here is the answers for this customer : The trusses in this particular case comes in 2 separate sections with a beam to attach the 2. However, it is better if he checks in locally with a truss manufacturer. The truss diagrams we provide are only shown for schematic purpose. It is the manufacturer’s responsibility to design and conceive the trusses to meet and comply local and code regulation. Thank you Kim
A: Good day, Unfortunately the truss information is on the plan only and it’s with the plan that the truss manufacturer can quote. We specialize in house plans only and therefore there is no assemble for our plans. Thanks Jessica
A: Hello, Our plans do not include wind load calculation, this would have to be checked into locally with an engineer. Here are the measurements requested : Top of ridge to walkout foundation(lowest point): 38’-10’’ Top of ridge to finish grade : 39’-6’’ Top of chimney to walkout foundation : 41’-10’’ Top of chimney to finish grade : 42’-6’’
A: Good morning! The lowest height of the sloped ceiling is approximately 4’-6’’ I hope this helps! Jessica
A: Good morning! The snow load for this plan is 75 pounds per square ft. Hope this helps! Jessica
A: Good day, The roof pitch for this plan is 14/12. The trusses are manufactured trusses. Hope this helps! Jessica
A: Good day, The exterior beams are decorative only but the roof is really manufactured trusses. Jessica
A: Hello, Our roof structures are manufactured trusses. I hope this helps! Jessica
A: Hi, The ceiling height on the first level is 8’-0’’except the cathedral part in the kitchen, dining room and living room that is ±25’-7’’ The second level is 8’-0’’ Regards.
A: Yes you can! Please click the "Modifications" tab above to get more information.
A: The national average for a house is running right at $125.00 per SF. You can get more detailed information by clicking the Cost-To-Build tab above. Sorry, but we cannot give cost estimates for garage, multifamily or project plans.
Have any Questions? Please Call 800-482-0464 and our Sales Staff will be able to answer most questions and take your order over the phone. If you prefer to order online click the button below.Add to cart